Automotive Diagnostic Tools


		Warranty \| Payments \| Shipping \| Returns \| Privacy Policy

Category:

Automovite Simulators

Oscilloscopes

		mScope
		mScope is high efficiency automotive motor tester. The mScope is specially designed for automobile test and analysis of ignition systems. Ignition waveform test function can be used to test the primary and secondary waveforms of gasoline engine and display them in single cylinder waveform and parade waveform. Read more...

		AutoScope Easy
		AutoScope EASY is system specially designed and tested as a cheap, reliable and easy to use tool for use primarily by automobile service professionals. It consists of a program in combination with the appropriate hardware adapter. Essentially this is a digital storage USB oscilloscope. It's also can be used for meassuring and recording slow-variable in time processes whose output value are an electrical signal or can be converted in such. Read more...

Oscilloscope's Accessories

		Piercing Test Clip
		With our piercing test clip, you can make contact with insulated wires without cutting or stripping insulation. Read more...

		Capacitive Pick-up Clamp
		Used for observing and measuring signals from the secondary ignition system's high-voltage spark plug wires. It can be used with both AutoScope Easy and mScope.

		Attenuator 10:1
		This is an addition to AutoScope Easy and mScope for measuring higher voltages. Its main purpose is to measure the control signals to the injectors.

		Attenuator 20:1
		This is an addition to AutoScope Easy and mScope for measuring higher voltages. Its main purpose is to measure the voltage from the primary ignition system and others.

		#1 Cylinder Trigger Pick-up Clamp
		Clipped on the spark plug wire to cylinder No. 1 to get the trigger signal that is used to identify the correct cylinder number of each ignition voltage signal.

		Pressure Pulse Sensor
		PPS detects such faults as burnt valves, bad injectors and other performance problems without major disassembly of the engine. To visualize the waveform of the output signal of PPS, its electrical part is connected to mScope or AutoScope Easy. Read more...

		CA-60 AC/DC Current Clamp
		The model CA-60 clamp adapter is transducer witch will allow your oscilloscope, motortester or multimeter to measure electrical current from 10 mA up to 60A, both types AC or DC, with a frequency response up to 20 kHz. In use for measuring current with this clamp adapter, there is not need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required. Read more...

		CA-600 AC/DC Current Clamp
		The model CA-600 clamp adapter is transducer witch will allow your oscilloscope, motortester or multimeter to measure electrical current up to 600 amperes, both types AC or DC, with a frequency response up to 400 Hz. In use for measuring current with this clamp adapter, there is not need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required. Read more...

		Acupuncture probe set
		The application of these acupuncture probe sets is for making measurements on the automobile electrical installation without damaging the entirety of the wires insulation. Read more...

		COP sensor
		The COP sensor can be used as an additional pick-up probe to any automobile oscilloscope. The COP sensor is used to test the efficiency of a COP ignition system, it is used to determine whether the COP system makes the ignition sparks it’s supposed to and their duration. Read more...

		Coil on Pug Extension Lead	*NEW*
		Universal Coil-on-Plug Extension Leads are capable of displaying ignition patterns from any lab scope. Read more...

		USB Isolator	*NEW*
		USB-to-USB Isolator protects your PC or Laptop while connecting USB peripherals wired to high voltages. Read more...

Automotive Sensor Simulators

		AutoSim
		AutoSim picks up a service problem where the on-board computer's diagnosis ends. Sensors tell the on-board computer something is wrong. AutoSim lets the technician determine if the faulty operation is a faulty sensor, a defect in the wiring or a problem in the computer itself. Read more...

		Resistor Box
		The Ditex’s Automotive Resistor Sensor Simulator is useful for simulation purposes in the automotive repair work, for inspection and testing applications of all car resistor type sensors. Read more...

Tools

		Fuel Injector Cleaner
		Ditex Injector Cleaner station is specially designed and tested as very effective and easy to use tool for cleaning of all types gasoline injectors. With this cleaning tool, you can restore all types of gasoline fuel injectors to like-new condition for a fraction of the cost of a new injector. Read more...

		Stepper Motor Tester
		The purpose of this tester for managing all types of stepping motors. It is specially designed and tested for stepper motors used in cars, but can also be used to test all the other stepping motors with a current through each coil does not exceed 0.75A. Read more...

		Piercing Test Clip
		With our piercing test clip, you can make contact with insulated wires without cutting or stripping insulation. Read more...

$refractometer$		Refractometer
		The automotive refractometer is designed for accurately measuring the strength of battery fluid, screenwash and antifreeze by measuring the refractive index of light passing through the mixture. Read more...

		Mercedes Dipstick
		The tools are designed to measure the oil level of the engine or the fluid level on late style 722.6XX series transmissions Read more...

		Common Rail Injector Back Leak Test Kit
		The back fuel volume from the injector is a good indicator of the deterioration or contamination of the injector. This kit is used to measure the back fuel quantity of the injectors for diesel engines with "Common Rail" injection system. It is suitable for the majority of European and Asian diesel cars. Read more...

		CA-60 AC/DC Current Clamp
		The model CA-60 clamp adapter is transducer witch will allow your oscilloscope, motortester or multimeter to measure electrical current from 10 mA up to 60A, both types AC or DC, with a frequency response up to 20 kHz. In use for measuring current with this clamp adapter, there is not need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required. Read more...

		CA-600 AC/DC Current Clamp
		The model CA-600 clamp adapter is transducer witch will allow your oscilloscope, motortester or multimeter to measure electrical current up to 600 amperes, both types AC or DC, with a frequency response up to 400 Hz. In use for measuring current with this clamp adapter, there is not need to break into the circuit or disturb the isolation as the opening jaws simply clamp around the current carrying conductor. No electrical contact is required. Read more...

		OBD Port Tester	*NEW*
		The purpose of the Advanced OBD diagnostic port tester is to make a full test of all kinds of 12V car diagnostic ports. A great cost effective time saver and stops damage to diagnostic equipment. Read more...

Car diagnostic cables

		OBD2 16pins connector

		OBD2 Breakout Box

		OBD2 female to 4 banana plugs
		Pinout Diagram

		OBD2 female to male

		Mercedes Benz Breakout Box

		OBD2 female to Mercedes 38 pin plug
		Pinout Diagram

Hanatech's Diagnostic Scanners

		Ultrascan P1
		Ultrascan P1 is a high quality compact scan tool for all occasions. Many workshops need a multifunctional tester. The Ultrascan P1 fulfills this desire. All "tools" necessary for troubleshooting are available in the tester. It is ideally suitable for independent workshops and fast fitters. Read more...

		Multiscan P2
		Multiscan P2 is a cost effective high tech hand-held solution for the automotive service professionals. It provides extensive in-depth vehicle coverage for a European, Japanese, Korean, USA, Australian, Malaysian, South American automobiles. MULTISCAN P2 features multi range control system coverage, ABS, SRS, ETS, Climate Control, ECM, PCM, Immobilizer, Cluster and much more. Supports extended functions such as reset basic settings, adaptation and activation. Read more...